Downloads (3)

Safety DataSheet296 KB
Technical DataSheet550 KB
XPREG Price List789 KB

Specification

Fabric Specification
Fibre SpecificsHigh Strength CF
Resin MatrixEpoxy
BrandXPREG
Fibre TypeCarbon Fibre
Fibre OrientationUnidirectional
WeaveUnidirectional
ColourBlack
TypeComponent Prepreg
Filament Count24K/50K
FormatUnidirectional
Fibre Properties
Freezer-life (at -18°C)12Months
UV ResistanceGood
Max Service Temp130°C
Filament Diameter7µm
Min Cure Temp80°C
Out-life (at 20°C)30Days
Max Cure Temp120°C
Typical Laminate Properties
Flexural Modulus60.1GPa
Tensile Strength645MPa
Flexural Strength882MPa
Interlaminar Shear Strength69.8MPa
Compressive Strength615MPa
Tensile Modulus55.2GPa
Tg Peak (DMA)148°C
Tg Onset (DMA)140°C
Weight and Dimensions
Areal Weight150g/m²
Consolidated Thickness0.15mm
Width300mm
Resin Weight37%
Suitable Uses
Suitable UsesAutoclave PrepregYes
General Properties
Gross Weight0.46kg
BrandXPREG

XC130 150g Unidirectional Prepreg Carbon Fibre (300mm)

Unidirectional reinforcement using our XPREG® XC130 resin system but 100% compatible with our XC110 system. This is an uncured prepreg material and requires an oven or autoclave to cure it.

This 150gsm UD reinforcement is used to add maximum possible strength in a specific direction. It can be used on its own or combined with woven reinforcements.

This prepreg reinforcement is 0.3m (300mm) wide and sold in a choice of prepacked roll lengths.


PRODUCT VERSIONS

Roll Length

AVAILABILITY:4 in stock available for immediate shipping

100 more can built in 2-3 days


PRICE
£24.28ex. VAT
(£40.47 /SQM)
4 in stock available for immediate shipping
QTY
ROLLS
ROLLS
We won’t be beaten on price!

If you believe you’re buying an equivalent product cheaper elsewhere, contact us to discuss your requirements.

150gsm unidirectional prepreg carbon fibre made using the XPREG® XC130 resin system. This 100% unidirectional reinforcement is entirely unsupported and so has no weft fibres to disrupt the the unidirectional fibres.

This UD prepreg can be used to add very specifically targeted (and oriented) strength to any composites component. Most typically, unidirectional reinforcement is used in conjunction with woven reinforcement to produce high performance components with strength exactly where it is needed.

This prepreg material can be used on its own or in conjunction with other XC130 prepregs (for autoclave or press curing). When cured in a press or autoclave this XC130 unidirectional prepreg can be used as any ply in the laminate, including the surface ply.

Use with XPREG® XC110 Out-of-Autoclave Prepreg

The XC130 resin system used in this prepreg is 100% compatible with the XPREG XC110 out-of-autoclave resin system and so this material can be used to add unidirectional reinforcement to laminates intended for out-of-autoclave cure.

When using XC130 prepregs (including this XC130 unidirectional carbon fibre prepreg) alongside XC110 prepregs for out-of-autoclave cure it is important to ensure that the first two plies down into the mould use the XC110 out-of-autoclave resin system. After the first two XC110 plies are down, XC130 prepregs (such as this unidirectional material) can be used without detriment to the surface finish.

How to Buy

This prepreg is supplied on a 300mm wide roll/tape and available in pre-rolled lengths of 2lm, 5lm, 10lm and the full 100lm roll.

Please choose the roll-length you require from the drop-down menu at the top of the page.

The Sample Pack Contains two 400x300mm (15.7x11.8") pieces of pre-preg.

For very large or ongoing requirements please contact our sales team.

150gsm unidirectional prepreg carbon fibre made using the XPREG® XC130 resin system. This 100% unidirectional reinforcement is entirely unsupported and so has no weft fibres to disrupt the the unidirectional fibres.

This UD prepreg can be used to add very specifically targeted (and oriented) strength to any composites component. Most typically, unidirectional reinforcement is used in conjunction with woven reinforcement to produce high performance components with strength exactly where it is needed.

This prepreg material can be used on its own or in conjunction with other XC130 prepregs (for autoclave or press curing). When cured in a press or autoclave this XC130 unidirectional prepreg can be used as any ply in the laminate, including the surface ply.

Use with XPREG® XC110 Out-of-Autoclave Prepreg

The XC130 resin system used in this prepreg is 100% compatible with the XPREG XC110 out-of-autoclave resin system and so this material can be used to add unidirectional reinforcement to laminates intended for out-of-autoclave cure.

When using XC130 prepregs (including this XC130 unidirectional carbon fibre prepreg) alongside XC110 prepregs for out-of-autoclave cure it is important to ensure that the first two plies down into the mould use the XC110 out-of-autoclave resin system. After the first two XC110 plies are down, XC130 prepregs (such as this unidirectional material) can be used without detriment to the surface finish.

How to Buy

This prepreg is supplied on a 300mm wide roll/tape and available in pre-rolled lengths of 2lm, 5lm, 10lm and the full 100lm roll.

Please choose the roll-length you require from the drop-down menu at the top of the page.

The Sample Pack Contains two 400x300mm (15.7x11.8") pieces of pre-preg.

For very large or ongoing requirements please contact our sales team.

Downloads (3)

Safety DataSheet296 KB
Technical DataSheet550 KB
XPREG Price List789 KB

Specification

Fabric Specification
Fibre SpecificsHigh Strength CF
Resin MatrixEpoxy
BrandXPREG
Fibre TypeCarbon Fibre
Fibre OrientationUnidirectional
WeaveUnidirectional
ColourBlack
TypeComponent Prepreg
Filament Count24K/50K
FormatUnidirectional
Fibre Properties
Freezer-life (at -18°C)12Months
UV ResistanceGood
Max Service Temp130°C
Filament Diameter7µm
Min Cure Temp80°C
Out-life (at 20°C)30Days
Max Cure Temp120°C
Typical Laminate Properties
Flexural Modulus60.1GPa
Tensile Strength645MPa
Flexural Strength882MPa
Interlaminar Shear Strength69.8MPa
Compressive Strength615MPa
Tensile Modulus55.2GPa
Tg Peak (DMA)148°C
Tg Onset (DMA)140°C
Weight and Dimensions
Areal Weight150g/m²
Consolidated Thickness0.15mm
Width300mm
Resin Weight37%
Suitable Uses
Suitable UsesAutoclave PrepregYes
General Properties
Gross Weight0.46kg
BrandXPREG
Can’t find the answer you’re looking for?Ask our technical team a question.

Unfortunately we do not stock any pre-pregs with a flexible resin. The only flexible resin we supply is our EF80 Flexible Epoxy Resin which is suitable for wet lay and vacuum bagged processes.

ASK YOUR OWN QUESTION

Note: Your name will be abbreviated and your email address will only be used to email you the answer directly

Note: Your name will be abbreviated and your email address will only be used to email you the answer directly

Customer Product Reviews for XC130 150g Unidirectional Prepreg Carbon Fibre (300mm)

No reviews

SUBMIT YOUR OWN PRODUCT REVIEW

We publish all reviews for verified purchases. Submit your own review and help other customers with their choices.

SUBMIT YOUR OWN PRODUCT REVIEW

We publish all reviews for verified purchases. Submit your own review and help other customers with their choices.

100% SECURE

    Secured by Digicert Payments by Adyen

PAYMENT METHODS

    Mastercard logo Visa logo Maestro logo PayPal logo Bank Transfer logo
    Staffordshire Chambers of Commerce member Composites UK member

Easy Composites Ltd, registered in England 7486797. All content copyright (C) Easy Composites Ltd, 2024. All rights reserved.